Running Speaker Wire

Share on Facebook You’ve just purchased watt speakers capable of a gust-busting 91 decibels, backed by a watt four-channel amplifier. The only problem here is that you’re a bit lacking in the wiring department and want to make sure you’ve correctly put together these monster noise machines all for the sake of blowing your neighbors out of their lounge chairs. Hooking up speakers to an amp is simple. Speaker wire comes in various gauges, lengths, resistance and capacities. Step Measure the distance from the amplifier to the speakers. If the speakers are close to the amplifier, say within 80 feet, gauge wire will do fine. If the speakers are further away, you need thicker wire to 14 gauge for better conductivity.

Stock CD player Honda accord hook up Subwoofers

One of the amplifiers powers the front “woofers” and the other powers the rear “woofers” All 4 tweeters are powered by the internal amplifier of the stock radio. I do not recommend using the new CD palyer to run the tweeters. It would help me to know exactly what Infinity reference speakers you are using, coaxials, component set, actual part ‘s The factory tweeters have no crossovers or bass blockers on them so if you run the Kenwood deck internal amp to them they will distort at a very low volume.

If you use only the new Infinity speakers and the new 4 channel amp you will get the best possible sound. When installing a new deck into the car you will need a harness that plugs into the factory radio plug. Metra part This harness is wired to the harness that comes with the new radio that you are installing.

Sep 24,  · How I have my door speakers wired to a 2 channel amp and still some sort of a fader. Short explanation.

The following is the most basic system. It involves a head unit HU and 2 pairs of speakers which are driven by the head unit’s internal amplifier. You can see that the battery terminal of the HU is connected to a constant source of power the battery with an inline fuse. The accessory wire for the HU is connected to a power source which only has power when the ignition switch is in the ‘on’ or ‘acc’ positions.

The battery and accessory connections will not be shown in the following diagrams but will be the same for all of the systems. The lines point to the speakers but the exact connection isn’t shown. The colored speaker wires from the HU are going to be connected to the positive speaker terminal of the speaker. The black or darker speaker wire will be connected to the negative speaker terminal.

Of course, this is just a generic type of diagram and you should consult the wiring diagram which was supplied with the HU. Using the HU’s internal amplifier and an external amplifier:

Anyone have Polaris door speakers

As I approach my golden years and continue gigging , the SVT is just not gonna work for me. Heard about Markbass in Bass Player, and bought it on a gamble. Read complete review As I approach my golden years and continue gigging , the SVT is just not gonna work for me. It is perfect for club gigs, gyms, even outdoor gigs. Recently a guy came out of the audience and said “Hey man, it kills me to say this ’cause I’m a bass player, but you’re too loud!

The more popular car amps drive four speakers: two front-door units and two backseat units generally mounted on the back deck under the rear window. With the front-door speakers’ wiring already pulled through the door and frame, all that remains is for you to connect the .

Hooking your speakers up to an amp is a quick process. If you know how to match colors, you can hook up your sound equipment rather easily. Read on for some tips on hooking up your speakers. To hook up speakers to an amp, you will need: This may seem silly, but it is better to be safe than sorry, especially if this is the first time you’ve connect speakers to an amp in your life.

Make sure the volume on the amp is also turned all the way down, to avoid harsh noises and speaker damage when you turn everything back on. The connectors on both the amplifier and your speakers are color-coded, with each terminal being either black or red in the majority of cases. The speaker cables are also color-coded, usually having the ends color-coded red and black or having the actual wires being copper and silver.

The copper wire corresponds to the red terminal. So all you have to do is match one end of a speaker wire to the same color terminals on the amp and repeat the process with the connectors on each speaker. Ensure the connections are tight. Loose connections mean noise and audio drop-out, so ensure your speaker and amp connections are snug as a bug. If your speaker wires have ends which are made of loose wire, twist them into a hard point before inserting them into the amplifier and speaker terminals.

Saab amp and speaker hook up stereo upgrade

Speaker selection and amplifier power ratings Too often we receive speakers for warranty repair in which the woofer voice coils are frozen and charred. The voice coil that drives the cone has overheated and burnt. Sometimes the speaker cone even catches fire! Often these are brought to us in the belief that the repair will be covered by warranty.

How do you hook up door speakers to an amp. But if you may seem daunting, weatherproof speakers to your phone to be rewarded with everyone. Yeah looks as painless as possible with two speakers. Yeah looks as painless as painless as if the io up to entertain your needs.

I am fairly familiar with upgrading audio on cars as I have done so on my last 2. I just had a couple of questions I couldnt find clear answers for on the forums and was hoping you guys could help, you seem like you know your stuff and I trust your opinions. Basically I have a 10″ JL w3 sub in a high output box and an amp i want to install when I get my car, and possibly upgrade the speakers.

I got the N head unit touchscreen with Nav from factory I was wondering if i could hook up the amp subs and speakers without messing up any of the audio controls, steering wheel controls, and uconnect and nav functions. My other 2 cars I used an aftermarket head unit, but i would like to keep this one as i paid for it! Just curious what my options were. Dont want to install if I cant get all of the factory features.

I know Chevy factory speakers produce no bass at all and sound like people screaming in a cardboard box into a pillow. So if you have not heard your car yet, I would wait before maybe swapping out the speakers.

SOLVED: Rear door speakers don’t work w/ aftermarket radio

The way that a tube amp behaves is different from a solid state amp. This is a rather complex issue but a few very simple rules can be followed to avoid any problems. I’ll say that 3db gave the best answer here. I have written extensively about this before in other forums and frankly, it comes up so often and because it is different for SS than for tube amps, that I have tired of answering it.

I do hate to see some info put out that could be harmful to someone but I can’t respond to every post on every forum so I hope that some others with some knowlege of the subject help out as well when it does come up.

Running the amp’s output wires to the wires on the adapter harness is how you avoid having to run new speaker wiring throughout the car. That’s the bottom side of the triangle in the photo — speaker wires from the amp connect to the speaker wires on the adapter harness. Then .

It is a cheapish Hilo uke so cheap that Guitar Center doesn’t like to admit they sell Read complete review During an extraordinary bout of procrastination, I decided to add a pick-up to my ukulele. It is a cheapish Hilo uke so cheap that Guitar Center doesn’t like to admit they sell them , and I was prepared to throw down whatever cash was needed to see what sort of sounds I could get out of it.

I’d done a little research on-line and settled for the Fender ’57 Mini Twin for a number of reasons, namely: Imagine my amusement when I walked into the store, asked for the Fender [Mini] Twin, and was shown to the full-sized amplifier. The sales rep’s face was priceless when I told him I planned to hook it up to an ukulele. Then, I explained that he’d misunderstood me and I was looking for the smaller version.

But the truth is, I’m quite surprised by how well it has performed.

4 ohm speakers on 8 ohm receiver

Tungsten So I took the crappy 9 speaker Alpine “Premium” system out of my car. I had the speakers replaced once already by the dealer and I am not replacing the same crappy speakers again so they can blow 2 weeks later. I went out and bought the following to redo my car’s audio system. After a couple hours I got a call from the technician there explaining to me how he cannot get a signal to my speakers.

Sep 20,  · Best Answer: You CAN hook up four speakers to a 2 channel amp. As long as the amp is “2 ohm stereo” stable, which virtually every single 2 channel amp is. And as long as each speaker is 4 ohms, which most car speakers are. You will lose fade capabilities, : Resolved.

Certified Quality Entertainment 3: If it’s too bass heavy, turn down your booth, not enough bass, turn it up a little. That’s more of a trial and error than saying keep them at the same level. As long as you are keeping your signal clean no red on your line meters and no red on your master meter, no clip lights blinking on your speakers you will be fine with adjusting as you need Ulrich von Hurtem 4: You need an active crossover.

I use and recommend a pre-owned Rane AC22B. Don’t just Y two outputs to one input, to get mono for the sub.

How to run amps, subs and speakers off stock headunit

From the separate tweeter to the upgraded crossover, component speakers mimic high-end home audio bookshelf speakers. Wiring these speakers into your vehicle offers an instant sonic upgrade over existing factory units, offering superior imaging, bass response and longevity. Essential Facts Component speakers are normally placed at the top of any car audio manufacturer’s line. Offering increased placement flexibility over conventional coaxial units, component speakers anchor the front soundstage of any serious car audio system.

Larger crossovers that divide the audio signal to the woofer and tweeter have superior internal components, capable of higher resolution sound and aiding in handling high power output from amplifiers.

There are two ways to wire four speakers to a two channel amplifier: in series or in parallel. Which one to choose depends on both the speakers and the amplifier, specifically their impedance levels and limits. Wiring speakers in series raises the impedance delivered to the .

I’m not going to waste my time by including a step my step process to every component of this install because they all ready exist. If you would like to see a step by step installation of removing door panels, running wire, running RCA cables and installing baffles click on Mr. Marv’s link above because he explains a basic set up for a double cab.

What I will show you is how to hook up an aftermarket amp to the stock stereo deck. Unplug The Car Battery Disclaimer: If you are not comfortable with any of the steps outlined in this DIY then do not attempt this project. That said I can not be responsible for any damage that occurs to your truck as a result of following the information contained within this thread. Remove Stock Head Unit If you don’t know how to remove the head unit I would follow from taco tunes its fairly easy.

Once you have the head unit out your dash will have the following harnesses exposed. The top two harnesses on the left that are circled are the ones that you will have to splice and add both RCA 4 and 2 channel converters.

Running Wires from 4 Channel Amp to Aftermarket Door Speakers

How to Install a Car Amp Installing car audio amplifiers is one of the trickiest things a newbie car audio installer can attempt. Car amp installation requires that all sorts of panels be removed and that various wires be run all over the car. Installing car audio amplifiers is a step by step process which I have outlined here. If you have any questions please contact me by clicking here.

Please do not attempt a car amp installation if you are not comfortable with the process. Leave it to a professional.

Oct 12,  · If you don’t have a mark or know the polarity of the wires, you may have to test the speakers prior to reinstalling the door. Powering the speakers with reverse polarity should not damage them unless you have a highly amplified system, but it is 31%(16).

They added an amp just for one more pair of door speakers on the 4-door models?!? Hardwarz crowdogg , Hardwarz Is that a question, or just a re-enforcement of what I am saying, lol? Hardwarz mygreen98 , I say the denali specifically, with the bose speakers. None of the speakers are hooked to the factory head unit. I was able to find the rear speaker wires which were coming out of the factory amp under the dash and got those working.

My question is what color wires go to the front speakers? I installed a fuse tap on the stereo fuse in the drivers door fusebox, ran a wire from that tap to the orange wire on the amp, back door speakers work! Next I guess I’m gonna disconnec the harness from the amp, tap into the wiring so my deck can power the rear door speakers directly, I’m just going to get rid of the tailgate ones, they sound like crap. Now, the amp has a white harness on one end, the other end has a black one that doesnt seem to be going anywhere, what is that?

I picked up a tahoe limited about a year ago, and just got around to upgrading the stereo.

Full Car Audio System Installation – Speakers, Subwoofer and Amplifier